Rockwell-automation 900 Temperature Controller Communications Function Manual do Utilizador descarregar pdf (Página 90)

Publication 900-UM004D-EN-E - July 2010

5-8 Communications Data for Modbus

➊ The program end output can be set when the Program Pattern is not set to 0 (OFF).

➋ This cannot be set if the Number of Multi-SP Uses parameter is set to 2.

➌ PRST: Program start can be set when the Program Pattern is not set to 0 (OFF) but the function will be disabled.

➍ P.END (program end output) can be set even when the program pattern is set to OFF, but the

function will be disabled.

➎ The output turns ON when the status of either the Control Output 1 ON/OFF Count Alarm or the

Control Output 2 ON/OFF Count Alarm turns ON.

Table 5.7

Address Parameter Name Setting (Monitor) Value Function

Group

Four-byte

mode

Two-byte

mode

0E0C 2E06 Control Output 1 Assignment When control output 1 is a linear output:

H'00000000 (0): Not assigned

H'00000001 (1): Control output (heating)

H'00000002 (2): Control output (cooling)

When control output 1 is an ON/OFF output:

H'00000000 (0): Not assigned

H'00000001 (1): Control output (heating)

H'00000002 (2): Control output (cooling)

H'00000003 (3): Alarm 1

H'00000004 (4): Alarm 2

H'00000005 (5): Alarm 3

H'00000006 (6): Program end output ➊

H'00000007 (7): Control output ON/OFF count alarm

Advanced

Setting

0E0E Control Output 2 Assignment H'00000000 (0): Not assigned

H'00000001 (1): Control output (heating)

H'00000002 (2): Control output (cooling)

H'00000003 (3): Alarm 1

H'00000004 (4): Alarm 2

H'00000005 (5): Alarm 3

H'00000006 (6): Program end output ➊

H'00000007 (7): Control output ON/OFF count alarm

0E14 2E0A Event Input Assignment 1 H'00000000 (0): None

H'00000001 (1): RUN/STOP (Cannot be set if the “Number of

multi-SP uses” is set to 1 or 2.)

H'00000002 (2): Auto/manual switch (Cannot be set if the

“Number of multi-SP uses” is set to 1 or 2.)

H'00000003 (3): Program Start (Cannot be set if the “Number

of multi-SP uses” is set to 1 or 2.)

➌

H'00000004 (4): Direct/reverse operation

H'00000005 (5): None

H'00000006 (6): 100% AT execute/cancel

H'00000007 (7): 40% AT execute/cancel

H'00000008 (8): Setting change enable/disable

H'00000009 (9): Communications writing enable/disable

H'0000000A (10): Alarm latch cancel

0E16 2E0B Event Input Assignment 2 ➋ H'00000000...H'0000000A (0...10) (Same settings as the Event Input

Assignment 1))

0E20 2E10 Auxiliary Output 1 Assignment H'00000000 (0): None

H'00000001 (1): Control output (heating)

H'00000002 (2): Control output (cooling)

H'00000003 (3): Alarm 1

H'00000004 (4): Alarm 2

H'00000005 (5): Alarm 3

H'00000006 (6): Program end output

➍

H'00000007 (7): Control output ON/OFF count alarm ➎

0E22 2E11 Auxiliary Output 2 Assignment H'00000000…H'00000007 (0…7) (Same settings as the Auxiliary

Output 1assignments)

0E24 2E12 Auxiliary Output 3 Assignment H'00000000…H'00000007 (0…7) (Same settings as the Auxiliary

Output 1assignments)

1 2 ... 85 86 87 88 89 90 91 92 93 94 95 ... 102 103

Comentários a estes Manuais

Sem comentários

Rockwell-automation 900 Temperature Controller Communications Function Manual do Utilizador Página 90

Comentários a estes Manuais

Manuais e produtos relacionados com Equipamento Rockwell-automation 900 Temperature Controller Communications Function