Rockwell-automation 1794-OF8IH FLEX Isolated Input/Output HART Analog Manual do Utilizador Página 83
- Página / 164
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Publication 1794-UM065B-EN-E - September 2010
1794-IF8IH and 1794-OF8IH Configuration 71
Fault Alarm (8 of 1 bit each)
Alarm signal for open wire channel fault, detected at <2 mA (<500 µA in
digital mode) and short circuit (R<42 in the 4…20 mA range, <86 in digital
mode, channel off).
This alarm is disabled when a data format is selected which includes 0 mA.
Range: 0=Normal, 1=Wire off/short circuit fault detected
Default: 0
Diagnostic Data (1 of 8 bits)
Response from module as to its condition.
14/O7 Read RealT Output Data Channel 6
15/EDT Read RealT Output Data Channel 7
Where: Fn : Channel n Fault alarm
Cn : Channel n HART Current Fault
Xn : HART Transmitter List
Dn : Channel n Digital out
1794-OF8IH Primary Data Table
Word/S
ISOC
Read/
Write
Data
Transport
Bit
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Diagnostic Status Value: 0 Channel Failure
0x00 All No Errors (default)
0x10 Channel 0 HART Iloop Threshold Configuration Error
0x11 Channel 1 HART Iloop Threshold Configuration Error
0x12 Channel 2 HART Iloop Threshold Configuration Error
0x13 Channel 3 HART Iloop Threshold Configuration Error
0x14 Channel 4 HART Iloop Threshold Configuration Error
0x15 Channel 5 HART Iloop Threshold Configuration Error
0x16 Channel 6 HART Iloop Threshold Configuration Error
0x17 Channel 7 HART Iloop Threshold Configuration Error
0x40 Channel 0 Format Configuration Error
0x41 Channel 1 Format Configuration Error
0x42 Channel 2 Format Configuration Error
0x43 Channel 3 Format Configuration Error
- Analog Modules 1
- Important User Information 2
- Summary of Changes 3
- Related Documentation 5
- Table of Contents 7
- 1794-IF8IH and 1794-OF8IH 8
- Table of Contents iii 9
- Table of Contents v 11
- What FLEX I/O Analog 13
- Modules Do 13
- Communicate with 14
- Programmable Controllers 14
- Physical Features of 15
- Your Module 15
- Use Alarms on the Input 15
- Overrange Alarm 16
- Underrange Alarm 16
- Remote Fault Alarm 16
- Local Fault Alarm 17
- Use the HART Capabilities 18
- HART Implementation 18
- Features 19
- Select Your Analog Input 20
- Module Operating Features 20
- Data Format 21
- Select Your Analog Output 22
- Latch Mode 23
- Global Reset 23
- Diagnostic Data error 11 24
- = data out of range 24
- Understand Image Table 25
- Mapping and Bit/Word 25
- Descriptions 25
- ATTENTION 27
- Install the Module 28
- Mount on a Panel or Wall 30
- Description Description 31
- IMPORTANT 32
- Label here 33
- Wire the Terminal Base 34
- Connect Wiring to the FLEX 34
- I/O HART Analog Modules 34
- Terminal Base Unit 35
- Ground the Module 36
- Use Programming Software 37
- About the ControlNet and 38
- EtherNet Adapters 38
- Communication Over the 38
- FLEX I/O Backplane 38
- Scheduled Data Transfer 39
- Unscheduled Data Transfer 39
- Module I/O Mapping 39
- I/O Structure 40
- Fault State Data 40
- Device Actions 40
- Data Transfer Types 43
- Configuration Parameters 44
- Byte Order (2 of 2 bits) 47
- Examples 49
- Fault Mode (8 of 1 bit) 50
- Low Alarm Limit (8 of 16 bit) 54
- Real Time Data (RTD) 57
- Profile, Primary Input 57
- Parameters 57
- Profile, Primary Status 58
- High Alarm (8 of 1 bit each) 60
- Low Alarm (8 of 1 bit each) 60
- Loop Alarm (8 of 1 bit each) 61
- HART Status Fields 63
- Secondary Input Data 64
- Table, Cyclic EDT Input 64
- HART PV Status (8 of 8 bits): 67
- Bit 5 Reserved 68
- Bit 6 Reserved 68
- Bit 7 Reserved 68
- HART PV Status 68
- Interpret the Status 69
- Indicators 69
- Module Configuration for 69
- Little Endian Byte Order 75
- Word Swap BYTE ORDER 75
- Profile, Status Parameters 82
- Fault Alarm (8 of 1 bit each) 83
- Diagnostic Data (1 of 8 bits) 83
- Profile, Output Parameters 85
- Global Reset (1 of 1 bit) 86
- Status Indicators 87
- Configure Module Messaging 89
- HART Configuration Quick 90
- Field Value Definition 100
- HART Failed Reason Code 104
- Chapter Summary 106
- Troubleshoot Your Module 107
- FLEX I/O HART Module Commands 109
- Commands 110
- Universal Commands 110
- Common Practice 110
- Device-specific Commands 111
- Appendix 113
- Overview 113
- Message Structure 113
- Burst Mode (not supported) 114
- Start Character 115
- HART Address 115
- HART Command 115
- Byte Count 116
- Check Byte 116
- Response Code 116
- Communication 127
- HART Frame Enhancements 130
- Background Information 131
- Configuration 132
- HART Disable 133
- Channel Data Format 133
- Channel Data Formats 134
- Digital Filters 135
- High Alarm Limit 138
- Low Alarm Limit 138
- Remote High High Alarm Limit 138
- Input Map 139
- High Alarm 140
- Low Alarm 140
- Out of Range 141
- Second Alarm 141
- Diagnostic Status 141
- HART Fault 142
- HART Current Fault 142
- HART Transmitter Present 143
- Local Fault Mode 147
- Digital Mode 152
- Digital Fault Mode 153
- Analog Fault Value 153
- HART Command 3 Disable 153
- Digital Data 154
- Fault Reset 154
- Analog Data 154
- 152 Index 160
- How Are We Doing? 161
- BUSINESS REPLY MAIL 162
- Rockwell Automation 164
Manuais e produtos relacionados com Equipamento Rockwell-automation 1794-OF8IH FLEX Isolated Input/Output HART Analog
Equipamento Rockwell-automation 2090-K2KSCLAMP-4 Kinetix 2000 Cable Clamp Bracket Manual do Utilizador
(4 páginas)
(4 páginas)
(4 páginas)
Equipamento Rockwell-automation 2707-M232P3_M485P3 DTAM Micro Operator Interface M Manual do Utilizador
(124 páginas)
(124 páginas)
Equipamento Rockwell-automation 57C329 Remote I/O Communications, AutoMax Manual do Utilizador
(144 páginas)
(144 páginas)
Equipamento Rockwell-automation 2364F RGU DC Suppressor Replacement Manual do Utilizador
(4 páginas)
(4 páginas)
Equipamento Rockwell-automation 6189x Integrated Display Industrial Computers User Manual do Utilizador
(124 páginas)
(124 páginas)
Equipamento Rockwell-automation 4100 REC Resolver to Encoder Converter Installatio Manual do Utilizador
(50 páginas)
(50 páginas)
Equipamento Rockwell-automation 2097-Rx Shunt Resistor Installation Instructions Manual do Utilizador
(8 páginas)
(8 páginas)
Equipamento Rockwell-automation 2707-NP DTAM Programming Software Manual do Utilizador
(184 páginas)
(184 páginas)
Equipamento Rockwell-automation 6185-A 10 Inch Monitor User Manual Manual do Utilizador
(31 páginas)
(31 páginas)
Equipamento Rockwell-automation 4100 ESRS Encoder Signal Reference Simulator Insta Manual do Utilizador
(37 páginas)
(37 páginas)
Equipamento Rockwell-automation 9528-APPOWSENE Virtual Image Templates User Manual Manual do Utilizador
(120 páginas)
(120 páginas)
Equipamento Rockwell-automation 1798-DFTP2 FlexArmor DeviceNet Field Termination P Manual do Utilizador
(8 páginas)
(8 páginas)
Equipamento Rockwell-automation 2090 Ultra3000 Servo Drives Integration Manual Manual do Utilizador
(180 páginas)
(180 páginas)
Equipamento Rockwell-automation 6181F_P Series E Integrated Display Computers Inst Manual do Utilizador
(24 páginas)
(24 páginas)
Equipamento Rockwell-automation 9220-CC QUICK START CONTROLNET NTWK Manual do Utilizador
(14 páginas)
(14 páginas)
Equipamento Rockwell-automation 6155R 200R VersaView Industrial Non-display Comput Manual do Utilizador
(24 páginas)
(24 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais