Rockwell-automation 284D On-Machine ArmorStart Accelerator Toolkit Manual do Utilizador Página 53
- Página / 188
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Publication IASIMP-QS015C-EN-P - August 2011 53
System Layout and Wiring Chapter 2
AC Supply Considerations for Bulletin 284 Units
This section describes AC supply considerations for Bulletin 284 units.
Ungrounded and High-resistive Distribution Systems
Disconnect MOVs
To prevent device damage, the MOVs connected to ground must be disconnected if the device is installed on
an ungrounded and high resistive distribution system where the line-to-ground voltages on any phase could
exceed 125% of the nominal line-to-line voltage. To disconnect the MOVs, follow this procedure to remove
the jumper.
1. Loosen the four mounting screws before installing the Bulletin 284 device.
2. Unplug the started module from the base unit by pulling forward.
ATTENTION
The Bulletin 284 device contains protective metal oxide variables (MOVs) that are referenced to ground.
These devices should be disconnected if the Bulletin 284 device is installed on an ungrounded and
high-resistive distribution system.
ATTENTION
Do not remove this jumper if the unit is equipped with an EMI filter installed.
The EMI Filter option is required if the Bulletin 284 ArmorStart Distributed Motor Controller must be
CE-compliant. If the EMI Filter is selected, a 3 meter shielded 4-conductor cordset is provided as standard.
is option is only available with sensorless vector control.
Jumper
- Quick Start 1
- Important User Information 2
- Where to Start 3
- Table of Contents 5
- About This Publication 9
- Required Software 10
- Conventions 10
- Additional Resources 11
- Hardware Selection 13
- Hardware Selection Chapter 1 15
- Chapter 1 Hardware Selection 16
- Configure Device Accessories 22
- View and Configure Network 29
- Add a Control Power Network 30
- Add a DeviceNet Network 32
- System Layout and Wiring 39
- Panel Layout Diagrams 42
- Sample Bill of Material 43
- Sample CAD Wiring Diagram 44
- General Precautions 46
- ArmorStart Device Wiring 47
- Secondary 48
- for available lengths 50
- Disconnect MOVs 53
- ATTENTION 54
- Electromagnetic Compatibility 56
- A on page 155 59
- Rockwell Automation website 61
- Verify Tags 69
- Consumed IO instance for the 70
- EtherNet/IP 71
- Device Tag Test Setup 72
- Test Procedure 73
- Build Your Logic Program 78
- Standalone Device 83
- DeviceLogix Example 84
- Network Input 0 Logic 85
- Input 1 Logic 85
- Flashing Stack Light Logic 85
- ArmorStart device 87
- Faceplate Logix Integration 89
- IMPORTANT 101
- Two Operator Rungs 102
- Download the Project 111
- FactoryTalk View Integration 113
- Follow These Steps 114
- 2. Check Initial Graphic 123
- beginning on page 124 132
- Add Alarm History Faceplate 133
- Test the Project 139
- Run the Project on a Terminal 142
- Before You Begin 145
- What You Need 145
- Navigation 151
- Configuring PC Communication 155
- Verify Your IP Address 156
- Assign IP Addresses 160
- Using DHCP 162
- 3. Click Next 164
- RSLinx software starts 164
- 5. Click OK 165
- 11. Click Cancel 167
- Load the Controller Firmware 168
- Appendix 173
- Appendix B 175
- DeviceNet Connector 179
- 193-DNCT Device 179
- 193-CM1 Cable 179
- Initial Screen 180
- Hand-held Terminal Keys 181
- Who display 182
- 2. Press 182
- Select and Monitor Parameters 183
- Monitor a Parameter 184
- Change Parameters 185
- Change a Numeric Parameter 186
- Rockwell Automation Support 188
- Documentation Feedback 188
Manuais e produtos relacionados com Equipamento Rockwell-automation 284D On-Machine ArmorStart Accelerator Toolkit
Equipamento Rockwell-automation SB3000 Configuration and Programming Manual do Utilizador
(122 páginas)
(122 páginas)
Equipamento Rockwell-automation 20D PowerFlex 700H/S Frame 13 Replacement Power St Manual do Utilizador
(20 páginas)
(20 páginas)
(4 páginas)
Equipamento Rockwell-automation T8834 Trusted 20 Channel Isolated AI/DI FTA Extern Manual do Utilizador
(18 páginas)
(18 páginas)
Equipamento Rockwell-automation 440F 440F-C252D 22.5mm Control Unit Safedge Manual do Utilizador
(2 páginas)
(2 páginas)
Equipamento Rockwell-automation TC500 Trusted I/O SmartSlot Cables Manual do Utilizador
(28 páginas)
(28 páginas)
Equipamento Rockwell-automation T8831 Trusted 40 Channel Analogue FTA Non-incendiv Manual do Utilizador
(14 páginas)
(14 páginas)
Equipamento Rockwell-automation Logix5000 Control Systems: Connect PanelView Plus Manual do Utilizador
(56 páginas)
(56 páginas)
Equipamento Rockwell-automation 1440-SPD02-01RB XM-220 Dual Speed Module Manual do Utilizador
(127 páginas)
(127 páginas)
Equipamento Rockwell-automation Solar Turbine Addendum Version 6.0 Manual do Utilizador
(34 páginas)
(34 páginas)
Equipamento Rockwell-automation T8891 Trusted Speed Monitor OFTA (SOFTA) Manual do Utilizador
(20 páginas)
(20 páginas)
Equipamento Rockwell-automation VSM-CE-1l, 3l, 3E Integrated Drive/Motor CE Filter Manual do Utilizador
(8 páginas)
(8 páginas)
Equipamento Rockwell-automation T7480 ICS Regent+Plus Guarded Analog Output Module Manual do Utilizador
(26 páginas)
(26 páginas)
Equipamento Rockwell-automation Zero Speed Configuring MaxPakPlus, DC-1, 1 3Phase Manual do Utilizador
(4 páginas)
(4 páginas)
Equipamento Rockwell-automation MinPak Plus DC Drive Field Supply Kit for RG 14C23 Manual do Utilizador
(4 páginas)
(4 páginas)
COBY electronic Digitální fotorámečky uživatelské příručky
Seznam produktů COBY electronic Digitální fotorámečky obsahuje 9 uživatelské příručky pro 9 modelů. Všechny uživatelské příručky pdf jsou k dispozici ke stažení nebo prohlížení online.
Comentários a estes Manuais