Rockwell-automation MD65 User Manual Version 2.0 Manual do Utilizador Página 47
- Página / 186
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Completing the Installation
7-1
CHAPTER 7
Completing the Installation
This chapter provides instructions on how to perform a final check of
the installation before and after power is applied to the drive.
7.1 Checking the Installation Before
Applying Power to the Drive
To verify the condition of the installation:
• Confirm that all inputs are connected to the correct terminals and
are secure.
• Verify that AC line power at the disconnect device is within the
rated value of the drive.
• Verify that any external digital control power is 24 volts DC.
!
ATTENTION: Only qualified electrical personnel
familiar with the construction and operation of this
equipment and the hazards involved should start and
adjust it. Read and understand this manual in its
entirety before proceeding. Failure to observe this
precaution could result in severe bodily injury or loss
of life.
!
ATTENTION:The drive contains high voltage
capacitors that take time to discharge after removal of
mains supply. Before working on the drive, ensure
isolation of mains supply from line inputs [R, S, T (L1,
L2, L3)]. Wait three (3) minutes for capacitors to
discharge to safe voltage levels. Darkened display
LEDs is not an indication that capacitors have
discharged to safe voltage levels. Failure to observe
this precaution could result in severe bodily injury or
loss of life.
ATTENTION: You must provide an external, hardwired
emergency stop circuit outside of the drive circuitry.
This circuit must disable the system in case of
improper operation. Uncontrolled machine operation
can result if this procedure is not followed. Failure to
observe this precaution could result in bodily injury.
- MD65 AC Drive 1
- User Manual 1
- Version 2.0 1
- CONTENTS 3
- Contents 5
- List of Figures 7
- List of Tables 9
- MD65 AC Drive User Manual 10
- CHAPTER 1 11
- CHAPTER 2 13
- 2.3 Kits and Accessories 15
- 2.4 Storage Guidelines 16
- CHAPTER 3 17
- Mounting the Drive 19
- 3.2 Mounting the Drive 22
- CHAPTER 4 23
- 4.1 RFI Filter Grounding 24
- CHAPTER 5 25
- Match Available Power 26
- Installing Power Wiring 27
- • Line reactor 28
- • Isolation transformer 28
- • Remove MOV jumper to 28
- Drive Ratings 31
- 200-600 Volt Installations 32
- 5.7 Reflected Wave Protection 34
- 5.8 Output Disconnect 34
- CHAPTER 6 35
- • Always use copper wire 36
- Recommendations 37
- Analog Output Select 38
- 30V DC 125V AC 240V AC 38
- Resistive 3.0 A 3.0 A 3.0 A 38
- Inductive 0.5 A 0.5 A 0.5 A 38
- Installing Control Wiring 39
- 6.4.1 I/O Wiring Examples 40
- Stop-Run 41
- 6.6 Accel/Decel Selection 45
- CHAPTER 7 47
- Complete 48
- CHAPTER 8 49
- 8.1.1 Display Description 50
- • Parameter number 50
- • Parameter value 50
- • Fault code 50
- 8.1.2 LED Descriptions 50
- Table 8.2 – Key Descriptions 51
- 8.2 About Parameters 52
- Advanced (A) Parameters 53
- CHAPTER 9 55
- P036 Start Source 57
- P037 Stop Mode 58
- P038 Speed Reference 59
- P039 Accel Time 1 60
- P040 Decel Time 1 60
- P041 Reset To Defalts 61
- P042 Voltage Class 61
- 9.2 Advanced Group Parameters 62
- A055 Relay Out Sel 65
- A056 Relay Out Level 67
- Opto Out1 Sel 68
- Opto Out2 Sel 68
- A065 Analog Out Sel 71
- A066 Analog Out High 72
- A067 Accel Time 2 72
- A068 Decel Time 2 72
- A069 Internal Freq 73
- A079 Jog Accel/Decel 75
- A080 DC Brake Time 75
- A081 DC Brake Level 75
- A082 DB Resistor Sel 76
- A083 S Curve % 76
- A084 Boost Select 77
- A085 Start Boost 78
- A086 Break Voltage 78
- A087 Break Frequency 79
- A088 Maximum Voltage 79
- A089 Current Limit 1 79
- A090 Motor OL Select 79
- A091 PWM Frequency 80
- A092 Auto Rstrt Tries 80
- A093 Auto Rstrt Delay 81
- A094 Start At PowerUp 81
- A095 Reverse Disable 81
- A096 Flying Start En 82
- A097 Compensation 82
- A098 SW Current Trip 82
- A100 Fault Clear 83
- A101 Program Lock 83
- A102 Testpoint Sel 83
- A103 Comm Data Rate 84
- A104 Comm Node Addr 84
- A105 Comm Loss Action 84
- A106 Comm Loss Time 85
- A107 Comm Format 85
- A108 Language 85
- A109 Anlg Out Setpoint 86
- A110 Anlg In 0-10V Lo 86
- A112 Anlg In4-20mA Lo 87
- A113 Anlg In4-20mA Hi 87
- A114 Slip Hertz @ FLA 87
- A115 Process Time Lo 87
- A121 Stall Fault Time 89
- A122 Analog In Loss 89
- A123 10V Bipolar Enbl 90
- A124 Var PWM Disable 90
- A125 Torque Perf Mode 91
- A126 Motor NP FLA 91
- A127 Autotune 91
- A128 IR Voltage Drop 92
- A129 Flux Current Ref 92
- A130 PID Trim Hi 92
- A131 PID Trim Lo 93
- A132 PID Ref Select 93
- A133 PID Feedback Sel 93
- A134 PID Prop Gain 93
- Range: 0.0 to 999.9 sec 97
- Default: 30.0 sec 97
- A160 EM Brk Off Delay 98
- A161 EM Brk On Delay 98
- A162 MOP Reset Sel 99
- 9.3 Display Group Parameters 100
- Running Bit 0 101
- Forward Bit 1 101
- Accelerating Bit 2 101
- Decelerating Bit 3 101
- MD65 AC Drive User Manual 102
- Parameter Descriptions 103
- Receiving Data Bit 0 104
- Transmitting Data Bit 1 104
- RS485 Option Connected Bit 2 104
- CHAPTER 10 107
- Feature) 108
- Troubleshooting the Drive 109
- • Cycle power 112
- • Replace drive if fault 112
- 10.2 Troubleshooting Tables 113
- APPENDIX A 119
- CSA 22.2 121
- APPENDIX B 123
- B.2 Advanced Parameter Group 124
- Record of User Settings 125
- APPENDIX C 129
- APPENDIX D 135
- MD60 AC Drive User Manual 136
- EN61000-3-2 137
- APPENDIX E 139
- E.1 Dynamic Brake Modules 140
- Frame Model Number 141
- E.2 EMC Line Filters 142
- Accessories 143
- Description Model Number 145
- APPENDIX F 149
- Parameter Configuration 150
- RS485 (MDI) Protocol 151
- Writing (06) Reference 153
- Reading (03) Feedback 154
- Codes) 155
- APPENDIX G 157
- Cable Accessories 158
- One Permanent Peripheral 159
- Connecting an RS485 Network 160
- APPENDIX H 161
- StepLogic 162
- Using Timed Steps 162
- Using Basic Logic Functions 163
- Timer Function 164
- Counter Function 166
- Parameters 167
- PPENDIX I 169
- Trim Control 170
- PID Reference and Feedback 171
- Analog PID Reference Signals 172
- PID Deadband 173
- PID Enabled 174
- Freq Cmd 174
- PID Output 174
- PID Pre-load Value 174
- PID Pre-load Value > 0 174
- PID Gains 175
- PID Feedback 176
- PID Reference 176
- PID Set Up 177
- Numerics 179
Manuais e produtos relacionados com Equipamento Rockwell-automation MD65 User Manual Version 2.0
Equipamento Rockwell-automation Flex/WebPak 3000 Operator Interface Module (OIM) K Manual do Utilizador
(4 páginas)
(4 páginas)
Equipamento Rockwell-automation T8297 Trusted Output Power Distribution Unit (Diod Manual do Utilizador
(10 páginas)
(10 páginas)
Equipamento Rockwell-automation FactoryTalk Alarms and Events Quick Start Manual do Utilizador
(246 páginas)
(246 páginas)
Equipamento Rockwell-automation T8472 Trusted TMR 120V ac Isolated Output Module Manual do Utilizador
(28 páginas)
(28 páginas)
Equipamento Rockwell-automation AADvance Controller Solutions Handbook Manual do Utilizador
(148 páginas)
(148 páginas)
Equipamento Rockwell-automation Isomag 4 Universal Guard Safety Switch Manual do Utilizador
(2 páginas)
(2 páginas)
Equipamento Rockwell-automation CEP7-EGF CEP7 Ground Fault Accessory Module Manual do Utilizador
(8 páginas)
(8 páginas)
Equipamento Rockwell-automation T8432 Trusted Dual Analogue Input Module Manual do Utilizador
(2 páginas)
(2 páginas)
Equipamento Rockwell-automation FlexPak 3000 115 VAC Control Opt. Board M/N 917FK0 Manual do Utilizador
(20 páginas)
(20 páginas)
Equipamento Rockwell-automation T80011 Application Note Application Variable Limit Manual do Utilizador
(4 páginas)
(4 páginas)
Equipamento Rockwell-automation FlexPak Plus Auxiliary Panel 14C330, 331, 332 Manual do Utilizador
(4 páginas)
(4 páginas)
Equipamento Rockwell-automation 1756-EN2TSC EtherNet/IP Secure Communication User Manual do Utilizador
(64 páginas)
(64 páginas)
Equipamento Rockwell-automation TAI16AEA 16- Channel Analogue Input Termination Mo Manual do Utilizador
(11 páginas)
(11 páginas)
COBY electronic Digitální fotorámečky uživatelské příručky
Seznam produktů COBY electronic Digitální fotorámečky obsahuje 9 uživatelské příručky pro 9 modelů. Všechny uživatelské příručky pdf jsou k dispozici ke stažení nebo prohlížení online.
Comentários a estes Manuais