Rockwell-automation Logix5000 Controllers Nonvolatile Memory Programmi Manual do Utilizador

Programming Manual Logix5000 Controllers Nonvolatile Memory Card Catalog Numbers 1756 ControlLogix, 1756 GuardLogix, 1768 CompactLogix, 1768 Compac

Chapter 1 Store and load a project by using a memory card These Logix5000 controllers support a memory card for project storage. C

Store and load a project by using a memory card Chapter 1 Prevent a major fault during a load If the major and minor revisions of

Chapter 1 Store and load a project by using a memory card If the revision of your project is Then 11.x The CompactFlash card uses a

Store and load a project by using a memory card Chapter 1 Perform firmware updates This table outlines the options and precautions

Chapter 1 Store and load a project by using a memory card When to load an image You have several options for when (under what condit

Store and load a project by using a memory card Chapter 1 This section explains how to store a project on the memory card of the c

Chapter 1 Store and load a project by using a memory card Important: At the bottom of the Nonvolatile Memory tab, a message appears

Store and load a project by using a memory card Chapter 1 In the Load Image field, if you choose On Power Up or On Corrupt Memory,

Chapter 1 Store and load a project by using a memory card When the store operation is finished, you remain offline. For procedures

Store and load a project by using a memory card Chapter 1 2. Did the Connected To Go Online dialog box open? If Then No a. Put

Important user information Read this document and the documents listed in the additional resources section about installation, configuration, and ope

Chapter 1 Store and load a project by using a memory card 5. At the bottom of the Image in Nonvolatile Memory area, click Load --&g

Store and load a project by using a memory card Chapter 1 Figure 1: Load and Update Examples on the Status Display When the contr

Chapter 1 Store and load a project by using a memory card Follow these steps to remove a project from a memory card. 1. Go online w

Store and load a project by using a memory card Chapter 1 Change the load image option 1. On the Nonvolatile Memory tab, click Lo

Chapter 1 Store and load a project by using a memory card Store the empty image 1. Go online with the controller. The Connected To

Store and load a project by using a memory card Chapter 1 5. Click Yes to store the project. The table describes the events that

Chapter 2 Use a memory card reader A sample controller project that reads and writes a memory card is available with the Logix Designer application.

Chapter 2 Use a memory card reader When you store a project to a memory card, you define: • When to load the project (On Power Up,

Use a memory card reader Chapter 2 Edit the Load Mode option of the project (does not apply if the Load Image option is User Init

Summary of changes This table contains the changes made to this revision. Change Topic Added support for the ControlLogix 5370 series of controller

Chapter 2 Use a memory card reader 30 Rockwell Automation Publication 1756-PM017F-EN-P – October 2014

1 1756-L7x controller SD card 15 1784-CF64 Industrial CompactFlash card format 11, 12 storage of firmware 13 1784-SD1 Secure Digital card fo

Index P parameters memory card 9 project load 19 load from nonvolatile memory 14, 19 nonvolatile memory 9, 27 store 15 R remove SD card 1

Rockwell Automation support Rockwell Automation provides technical information on the web to assist you in using its products. At http://www.rockwell

Table of contents Studio 5000 environment ... 7 Additional resource

Preface This manual shows you how to access and use a memory card in Logix5000 controllers. This manual is one of a set of related manuals that show

Preface You can view or download publications at http://www.rockwellautomation.com/literature. To order paper copies of technical documentation, cont

Chapter 1 Store and load a project by using a memory card The memory card allows you to keep a copy of your project on the controller without the nee