Rockwell-automation 150 USE MN/SMC DIALOG + CONTROLLER Manual do Utilizador descarregar pdf (Página 158)

Troubleshooting

10-9

500–1000 Amp

Refer to Figure 10.4 for control module removal reference.

1. Disconnect all control wires to control modules.

2. Loosen six control module screws.

3. Unplug control module from interface board by pulling forward.

Figure 10.4 Removal of Control Module (500–1000A)

(1) (2)

1 2 ... 153 154 155 156 157 158 159 160 161 162 163 ... 188 189

User Manual 1
Please Read! 2
Important User Information 2
Table of Contents 3
Table of Contents 10
Product Overview 11
Starting Modes 12
Selectable Kickstart 13
Current Limit Start 13
Percent 14
Voltage 14
Time (seconds) 14
Energy Saver 15
Phase Rebalance 15
Protection and 15
Protection and Diagnostics 16
Line Faults 19
Underload 19
Metering 20
Communication 21
Programming 21
Status Indication 21
Control Options 22
Pump Control Option 23
Preset Slow Speed Option 23
Control Options (cont.) 24
Accu-Stop 25
Installation 27
General Precautions 28
Heat Dissipation 28
Enclosures 28
Ventilated Enclosures 29
Non-ventilated Enclosures 29
Mounting 30
Mounting (cont.) 32
Power Factor 35
Correction Capacitors 35
Current-limiting 36
Fast Acting 36
Protective Modules 37
Motor Overload 37
Protection 37
Human Interface Module 38
Human Interface 40
Module (cont.) 40
“Comm Fault” will occur 41
Converter Modules 42
Converter Modules (cont.) 44
Electromagnetic 44
Compatibility (EMC) 44
Accessory Requirements 45
Chapter 3 47
Terminal Locations (cont.) 48
Power Wiring 49
Control Power 50
Fan Power 51
Control Terminal 52
Designations 52
Grounding 52
Provision 52
Standard Controller 53
Wiring Diagrams 53
Wiring Diagrams (cont.) 54
Programming Menu (cont.) 66
Password 69
Parameter Management 70
Using Parameter Management 71
Parameter Modification 72
Soft Start 73
Dual Ramp Start 74
Full Voltage Start 74
Basic Setup 75
Advanced Setup 76
Example Settings 77
Calibration 79
Motor Data Entry (cont.) 80
Calibration Procedure 81
Calibration Procedure (cont.) 82
Viewing Metering 84
Data (cont.) 84
Chapter 7 85
Programming Parameters 87
Control Wiring for 89
SCANport Control 89
Soft Stop, Pump Control, and 89
Controller Interfacing 93
Soft Stop Option 95
Accu-Stop Options 98
Contactor 100
Preset Slow Speed and 102
Accu-Stop Options (cont.) 102
Preset Slow Speed 103
Accu-Stop Option 104
Customer supplied 105
Serial Communications 110
Control Enable 111
SMC Status Data 112
Reference/Feedback 112
Parameter Listing 112
Scale Factor 112
Conversion 112
Display Unit 113
Equivalents 113
Datalinks 113
Interfacing 113
Processing Time 113
Remote I/O Examples 114
Remote I/O Examples (cont.) 115
G File Configuration 116
I/O Addressing 116
Block Transfer Instructions 130
DeviceNet Examples 133
I/O Mapping 134
Refer To Table 8.A 137
Explicit Messaging: 138
Examples 140
Sequence of Events: 140
Setting Up the Data File: 141
Example Ladder Logic Program: 142
Diagnostics 144
Clear Fault (cont.) 145
Fault Buffer 145
Fault Auxiliary Contact 145
Fault Definitions 146
Open Gate 148
Excess Starts/Hour 148
Controller Temp 148
Comm Fault 148
Troubleshooting 150
Control Module Removal 155
180–360 Amp 156
500–1000 Amp 158
Control Module Replacement 159
Protective Cover Removal 159
MOV Fuse 160
Replacement 160
Power Module and Interface 160
Board Resistance Check 160
180-1000 Amp 162
Specifications 164
Refer to product nameplate 165
Parameter Information 170
Renewal Parts 176
Accessories 180
Glossary 181
Glossary-2 182
Glossary-3 183
Glossary-4 184
40055-145-01(C) 189

Comentários a estes Manuais

Sem comentários

Rockwell-automation 150 USE MN/SMC DIALOG + CONTROLLER Manual do Utilizador Página 158

Comentários a estes Manuais

Manuais e produtos relacionados com Equipamento Rockwell-automation 150 USE MN/SMC DIALOG + CONTROLLER