Rockwell-automation 8520-GUM 9/Series CNC Grinder Operation and Progra Manual do Utilizador descarregar pdf (Página 43)

Chapter 2

Operating the Control

2-23

To reset the emergency stop state, press the <E-STOP RESET> button. Once

you push the E--Stop Reset button to clear the E--Stop state, the message,

“RESETTING E--STOP” displays to aler t you that the control is attempting

to come out of E--S top. After the cause of the E--Stop is resolved, t he

control clears the “E--STOP” message. If the error condition is not cleared,

the “RESETTING E--STOP” message clears, but the “E--STOP” message

continues to flash as the control remains in E--Stop state.

If the E-Stop occurred during program execution, the control resets the

program when you perform an E-Stop reset (provided AMP is configured

to perform a control reset or E-Stop reset). Assuming that you perform a

control reset, program execution begins from the 1st block of the program

when you press

<CYCLE START>. If the current axis position prohibits this,

the operator can manually jog the axes clear, or consider executing a

mid-program start (see page 7-13). If you do not perform a control reset or

E-Stop reset, the control aborts the remainder of the program block being

executed when E-Stop took place, and a

<CYCLE START> begins program

execution at the next block.

Important: If you do not eliminate the cause of the E-Stop, the circuit

connected to the E-STOP STATUS terminals on the sub-basic board

remains open, and the emergency stop state is not reset even when you

press the

<E-STOP RESET> button.

Reciprocation stops when an emergency stop condition occurs. No motion

occurs when the emergency stop is reset. If your control’s AMP is

configured such that the control is not

reset after an E-Stop reset, then

typically reciprocation resumes with the next cycle start. This allows part

programs to be resumed immediately without having to first restart

reciprocation. For details, see the documentation prepared by your system

installer.

Access control lets your system installer assign different functions of the

control to different users by means of a password. See page 2-28 for a list

of the functions that can be protected on the control.

Each protectable function is assigned an access level that is made active

when the operator enters his password. When an access level is made

active, all functions that are assigned to that access level become available.

Access levels range between 1 and 8 where 1 is the highest level and 8 is

the lowest. A different password is assigned to each of the different access

levels. You can assign a total of 8 passwords.

Important: If you do not want to use password protection, select all

functions as accessible for access level 8. Since access level 8 is

automatically available at power-up, no password is necessary to access

any of the functions of the control. You can also disable password

2.7

Access Control

1 2 ... 38 39 40 41 42 43 44 45 46 47 48 ... 819 820

Comentários a estes Manuais

Sem comentários

Vivanco WTL 3 Provozní pokyny (1 strany)

Značka: Vivanco | Kategorie: Flat panel wall mounts | Velikost: 0.68 MB |

Němec

Francouzština

Italština

Portugalština

Slovenština

Tabulka s obsahem

SINGLE ARM

1

Další produkty a příručky pro Nástěnné držáky pro ploché obrazovky Vivanco

Modely	Typ Dokumentu
MT 2615	Uživatelský manuál Vivanco MT 2615, 1 stránky
WTL 2	Provozní pokyny Vivanco WTL 2, 1 stránky
WTL 4	Provozní pokyny Vivanco WTL 4, 1 stránky
WTL 1	Provozní pokyny Vivanco WTL 1, 1 stránky
WTS 2	Provozní pokyny Vivanco WTS 2, 1 stránky
33392	Uživatelský manuál Vivanco 33392 flat panel wall mount [en] , 4 stránky
MP4735	Manuál s instrukcemi Vivanco MP4735 flat panel wall mount, 2 stránky
WTS 4	Provozní pokyny Vivanco WTS 4, 1 stránky
ULTRA SLIM 400	Uživatelský manuál Vivanco ULTRA SLIM 400, 1 stránky
WTL 6	Provozní pokyny Vivanco WTL 6, 2 stránky
WTS 1	Provozní pokyny Vivanco WTS 1, 1 stránky
WTS 3	Provozní pokyny Vivanco WTS 3, 1 stránky
WM 3735	Uživatelský manuál Vivanco WM 3735, 2 stránky
MF 2615	Uživatelský manuál Vivanco MF 2615, 1 stránky