Rockwell-automation 2755 AtomScan Bar Code Reader Manual do Utilizador Página 62
- Página / 141
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
5–17Configuring Your Reader
Publication 2755-6.9
Code 39
• Status
• Check Digit. Code 39 is self-checking and does not normally
require a check digit. However, for additional data integrity, a
Modulus 43 check digit can be added to the bar code message.
With Check Digit and an External or Serial Trigger option
enabled, an invalid check digit calculation will cause a no read
message to be transmitted at the end of the read cycle.
• Check Digit Output. When enabled, the check digit character is
sent along with the label data. When disabled, label data is sent
without the check digit.
• Large Intercharacter Gap. Allows the reader to read labels with
gaps between bar code characters exceeding three times the
narrow element width.
• Fixed Code Length. Used to increase data integrity by ensuring
that only one label length will be accepted.
• Code Length. Allows you to specify the exact number of
characters that the reader will recognize (this does not include
start and stop). The reader will ignore any code not having the
specified length.
Note: Fixed Code Length must be enabled for Code Length to
take effect.
Codabar
• Status
• Start and Stop Match. Requires the Codabar start and stop
characters (a, b, c, or d) to match before a valid read can occur.
• Start and Stop Output. Allows the start and stop characters to be
transmitted with bar code data.
• Large Intercharacter Gap. Allows the reader to read labels with
gaps between bar code characters exceeding three times the
narrow element width.
• Fixed Code Length. Used to increase data integrity by ensuring
that only one label length will be accepted.
• Code Length. Allows you to specify the exact number of
characters that the reader will recognize (this does not include
start and stop). The reader will ignore any code not having the
specified length.
Note: Fixed Code Length must be enabled for Code Length to
take effect.
• Check Digit. Allows you to select the type of checksum system
Codabar will use.
- AtomScan 1
- Code Readers 1
- Allen-Bradley 1
- Important User 2
- Information 2
- Table of Contents 3
- Configuring Your Reader 4
- Hardware Operation 4
- Table of Contents toc–iii 5
- Chapter Objectives 7
- Contents of this Manual 7
- Conventions Used in this 8
- Intended Audience 8
- Related Publications 8
- Introduction to AtomScan 9
- Procedures 10
- 3. Install the reader 11
- 4. Install the interface box 12
- 5. Install the power supply 12
- • baud rate = 9600 13
- • parity = even 13
- • stop bits = one 13
- • data bits = 7 13
- Hardware Features 16
- Interface Box Features 17
- Decoding 18
- Safety Information 19
- Scan Beam Options 20
- Accessories 20
- Designing Your Scanner System 21
- Symbol Height and Length 22
- Symbol Quality 22
- Symbol Orientation 23
- Direction 24
- Tilt, Pitch, and Skew 25
- Determining Read Range 26
- Calculating the Number of 29
- Picket Fence Calculation 30
- Installing Your Hardware 31
- Installing the System 32
- Hardware 32
- 4–4 Installing Your Hardware 34
- Mounting Surface 34
- Connecting System 35
- Hardware Together When 35
- Using an Interface Box 35
- Using an Interface Box in a 41
- Daisy-Chain Configuration 41
- 4–14 Installing Your Hardware 44
- Not Using an Interface Box 45
- 5–4 Configuring Your Reader 49
- [Control]. It 49
- [0] (zero) 49
- Communications Menu 50
- Host Protocol Parameters 51
- 5–7Configuring Your Reader 52
- Operations Menu 54
- 5–13Configuring Your Reader 58
- 5–14 Configuring Your Reader 59
- Code Types Menu 60
- 5–17Configuring Your Reader 62
- 5–18 Configuring Your Reader 63
- • Status 64
- Scanner Output Menu 65
- 5–22 Configuring Your Reader 67
- Scanner Setup Menu 68
- Serial Configuration 69
- Concatenating Serial Commands 70
- Serial Command Status Request 70
- Losing Communications 70
- Serial Configuration Commands 71
- Sserial command status,serial 72
- • Auxiliary Port 76
- • External Trigger Level 77
- • Match Code Type 77
- • New Master Pin 78
- • Narrow Margins 78
- • Bar Code Output 81
- • Beeper 82
- • Laser On/Off 82
- • Serial Verification 82
- Decode Test 84
- Adjusting Reader 84
- Parameters 84
- Scan Width 85
- Label Speed 85
- Status Commands 91
- Operating Scanner System 94
- • Postamble = CR (^M) 95
- • Postamble is enabled 95
- • transparent 96
- • non–buffered full-duplex 96
- • non-buffered half-duplex 96
- 6–14 Hardware Operation 99
- [<Zd>] (Restore/Save 99
- Reader RS-232RS-232 IB1 Host 99
- Publication 2755-6.9 100
- Operating the Power Supply 101
- Operating the Host Device 101
- Chapter 7 102
- Troubleshooting the 103
- Technical Support Services 104
- Specifications 105
- Reader Specifications 106
- Interface Box 107
- Power Supply 107
- Cable Pinouts 108
- Interface Box Pinouts 109
- Scanner Port 110
- RS-485/422 Port 110
- RS-232 Port 111
- ASCII Table 112
- Multidrop Communications 113
- Polling Sequence 115
- Select Sequence 116
- Application Examples 117
- Flexible Interface Module 119
- Application Examples E–5 121
- Module data 122
- SLC 5/03 and SLC 5/04 123
- Controllers 123
- SLC Program 126
- PLC-5 Controller 127
- PLC-5 controllers 128
- PLC-5 Controllers Setup 129
- DTAM Plus DeviceNet 130
- DeviceNet Operation 132
- Application Examples E–17 133
- European Union Directives 134
- Declaration of Conformity 135
- Glossary 136
- GlossaryG–2 137
- Glossary G–3 138
- GlossaryG–4 139
- Glossary G–5 140
- Worldwide representation 141
Manuais e produtos relacionados com Equipamento Rockwell-automation 2755 AtomScan Bar Code Reader
Equipamento Rockwell-automation 2711-NC21, -NC22 PanelView to MicroLogix Cable Manual do Utilizador
(2 páginas)
(2 páginas)
Equipamento Rockwell-automation 7712 OneGear Motor Control Center FVNR Starter (7. Manual do Utilizador
(52 páginas)
(52 páginas)
Equipamento Rockwell-automation 2080-LC30-24QWB_24QVB_24QBB Micro830 24 Point Prog Manual do Utilizador
(20 páginas)
(20 páginas)
Equipamento Rockwell-automation 2364E Non-Regenerative DC Bus Supply Unit (NRU) Manual do Utilizador
(93 páginas)
(93 páginas)
Equipamento Rockwell-automation 2030-MLXxxx-SYSx System Multiplexer / Permissive M Manual do Utilizador
(8 páginas)
(8 páginas)
Equipamento Rockwell-automation 2711P-RAK4 Cutout Adapter Kit for PVPlus 400 Keypa Manual do Utilizador
(40 páginas)
(40 páginas)
Equipamento Rockwell-automation 9101-1183, formerly 9101-1079 200 Watt Passive Shu Manual do Utilizador
(12 páginas)
(12 páginas)
Equipamento Rockwell-automation 2100 Replacing Line Terminal Guards Manual do Utilizador
(2 páginas)
(2 páginas)
Equipamento Rockwell-automation 2706 Dataliner DL40 Installation Instructions Manual do Utilizador
(16 páginas)
(16 páginas)
Equipamento Rockwell-automation 2711E-xxxx PanelView Operator Terminals User Manua Manual do Utilizador
(188 páginas)
(188 páginas)
Equipamento Rockwell-automation 2090 Low Profile Connector Kits Install Instructio Manual do Utilizador
(4 páginas)
(4 páginas)
Vivanco WTL 3 manuály
Uživatelské manuály a uživatelské příručky pro Nástěnné držáky pro ploché obrazovky Vivanco WTL 3.
Poskytujeme 1 manuály pdf Vivanco WTL 3 ke stažení zdarma podle typů dokumentů: Provozní pokyny
Comentários a estes Manuais