Rockwell-automation 1769-ADN Compact I/O DeviceNet Adapter Manual do Utilizador descarregar pdf (Página 15)

Compact I/O 1769-ADN DeviceNet Adapter 15

Rockwell Automation Publication 1769-IN001C-EN-P - February 2013

Steps to Replace the Adapter

The adapter can be replaced while the system is mounted to a panel (or DIN rail).

1. Remove power. See important note on page 6.

2. Remove the DeviceNet cable from the module by removing the connector.

3. Remove the upper and lower mounting screws from the adapter (or open the DIN

latches using a flat-blade or phillips-style screwdriver).

4. On the right-side adjacent module, move its bus lever to the right (unlock) to disconnect

it from the adapter being removed.

5. Gently slide the disconnected adapter forward.

If you feel excessive resistance, make sure that you disconnected the adapter from the

bus and that you removed both mounting screws (or opened the DIN latches).

6. Before installing the replacement adapter, be sure that the bus lever on the right-side

adjacent module is in the unlocked (fully right) position.

7. Slide the replacement adapter into the open slot.

8. Connect the adapter and modules together by locking (fully left) the bus levers on the

right-side adjacent module.

9. Replace the mounting screws (or snap the adapter onto the DIN rail).

10. Replace the DeviceNet cable on the module by attaching the connector to the module.

11. Set the network address switches to the same value as the removed adapter.

Field Wiring Connections

Grounding the Adapter

This product is intended to be mounted to a well-grounded mounting surface such as a metal

panel. Additional grounding connections from the adapter’s mounting tabs or DIN rail (if used),

are not required unless you cannot ground the mounting surface. Refer to Industrial Automation

Wiring and Grounding Guidelines, publication 1770-4.1

, for additional information.

TIP

It may be necessary to rock the module slightly from front to back to remove it, or,

in a panel-mounted system, to loosen the screws of adjacent modules.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 27 28

Sem comentários

Modely	Typ Dokumentu
MT 2615	Uživatelský manuál Vivanco MT 2615, 1 stránky
WTL 2	Provozní pokyny Vivanco WTL 2, 1 stránky
WTL 4	Provozní pokyny Vivanco WTL 4, 1 stránky
WTL 1	Provozní pokyny Vivanco WTL 1, 1 stránky
WTS 2	Provozní pokyny Vivanco WTS 2, 1 stránky
33392	Uživatelský manuál Vivanco 33392 flat panel wall mount [en] , 4 stránky
MP4735	Manuál s instrukcemi Vivanco MP4735 flat panel wall mount, 2 stránky
WTS 4	Provozní pokyny Vivanco WTS 4, 1 stránky
ULTRA SLIM 400	Uživatelský manuál Vivanco ULTRA SLIM 400, 1 stránky
WTL 6	Provozní pokyny Vivanco WTL 6, 2 stránky
WTS 1	Provozní pokyny Vivanco WTS 1, 1 stránky
WTS 3	Provozní pokyny Vivanco WTS 3, 1 stránky
WM 3735	Uživatelský manuál Vivanco WM 3735, 2 stránky
MF 2615	Uživatelský manuál Vivanco MF 2615, 1 stránky

Rockwell-automation 1769-ADN Compact I/O DeviceNet Adapter Manual do Utilizador Página 15