Rockwell-automation 842E CM Integrated Motion Encoder on EtherNet/IP Manual do Utilizador descarregar pdf (Página 25)

Rockwell Automation Publication 842E-UM002A-EN-P - November 2013 25

Chapter 4

Configuring the Encoder

Configuring the 842E-CM

Encoder IP Address

This section offers guidance on configuring your Ethernet connection to

the 842E-CM encoder.

Ethernet Connection

Configuration, programming, and diagnosis of the encoder are

performed over the standard 10/100 Mbps Ethernet communication port

by using the Logix Designer application.

842E-CM Encoder Port Configuration

The IP address of the 842E-CM encoder is composed of four octets

separated by three dots to conform to the Class C Subnet structure. Each

octet can be configured with a number between 1 and 254.

There are two methods of changing the current IP address. An address

can be automatically assigned to the encoder (dynamic IP address) when

the encoder is connected to a DHCP (Dynamic Host Configuration

Protocol) enabled server, or you can manually assign a IP address to the

encoder (static IP address). Both methods of configuring the encoder’s IP

address are shown here.

Setting the IP Address

The 842E-CM encoder is shipped with the network address switches set

to 999. You must assign the encoder an IP address using one of the two

methods outlined below.

Set the IP address of the 842E-CM encoder using either one of the

following methods:

1. Use the network address switches (see figure on page 26) on the

encoder to set the last octet of the IP address (192.168.1.xxx).

2. Use the network address switches to enable BootP / DHCP and use

a BootP utility or DHCP server to assign the IP address of the unit on

powerup.

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 63 64

Comentários a estes Manuais

Sem comentários

Modely	Typ Dokumentu
MT 2615	Uživatelský manuál Vivanco MT 2615, 1 stránky
WTL 2	Provozní pokyny Vivanco WTL 2, 1 stránky
WTL 4	Provozní pokyny Vivanco WTL 4, 1 stránky
WTL 1	Provozní pokyny Vivanco WTL 1, 1 stránky
WTS 2	Provozní pokyny Vivanco WTS 2, 1 stránky
33392	Uživatelský manuál Vivanco 33392 flat panel wall mount [en] , 4 stránky
MP4735	Manuál s instrukcemi Vivanco MP4735 flat panel wall mount, 2 stránky
WTS 4	Provozní pokyny Vivanco WTS 4, 1 stránky
ULTRA SLIM 400	Uživatelský manuál Vivanco ULTRA SLIM 400, 1 stránky
WTL 6	Provozní pokyny Vivanco WTL 6, 2 stránky
WTS 1	Provozní pokyny Vivanco WTS 1, 1 stránky
WTS 3	Provozní pokyny Vivanco WTS 3, 1 stránky
WM 3735	Uživatelský manuál Vivanco WM 3735, 2 stránky
MF 2615	Uživatelský manuál Vivanco MF 2615, 1 stránky

Rockwell-automation 842E CM Integrated Motion Encoder on EtherNet/IP Manual do Utilizador Página 25

Comentários a estes Manuais

Vivanco WTL 3 manuály

Vivanco WTL 3 Provozní pokyny (1 strany)

Tabulka s obsahem

Další produkty a příručky pro Nástěnné držáky pro ploché obrazovky Vivanco

Rockwell-automation 842E CM Integrated Motion Encoder on EtherNet/IP Manual do Utilizador Página 25

Comentários a estes Manuais

Manuais e produtos relacionados com Equipamento Rockwell-automation 842E CM Integrated Motion Encoder on EtherNet/IP

Vivanco WTL 3 manuály

Vivanco WTL 3 Provozní pokyny (1 strany)

Tabulka s obsahem

Další produkty a příručky pro Nástěnné držáky pro ploché obrazovky Vivanco