Rockwell-automation 1794-IF8IH FLEX I/O 8 Isolated Input HART Analog M Manual do Utilizador

Installation InstructionsFLEX I/O Isolated Input HART Analog ModuleCatalog Number 1794-IF8IH Topic PageImportant User Information 2Environment and Enc

10 FLEX I/O Isolated Input HART Analog Module Publication 1794-IN115C-EN-P - April 2009Ground the ModuleAll I/O wiring must use shielded wire. Shie

FLEX I/O Isolated Input HART Analog Module 11Publication 1794-IN115C-EN-P - April 2009Module Wiring 0

12 FLEX I/O Isolated Input HART Analog Module Publication 1794-IN115C-EN-P - April 2009Wire ConnectionsChannel Signal Ty peLabel MarkingsCatalog N

FLEX I/O Isolated Input HART Analog Module 13Publication 1794-IN115C-EN-P - April 2009Input Map Word Bit15141312111098765432100 Channel 0 Input Da

14 FLEX I/O Isolated Input HART Analog Module Publication 1794-IN115C-EN-P - April 2009Configuration MapWord Bit15141312111098765432100RRF7F6F5F4BO

FLEX I/O Isolated Input HART Analog Module 15Publication 1794-IN115C-EN-P - April 200929…32Words 9…12 for channel 533…36Words 9…12 for channel 637

16 FLEX I/O Isolated Input HART Analog Module Publication 1794-IN115C-EN-P - April 2009Cn HART CMD 3 Disable 0: HART CMD 3 communications enabled1:

FLEX I/O Isolated Input HART Analog Module 17Publication 1794-IN115C-EN-P - April 20094.17 Hz 5 101Not applicable 6 1 1 0Not applicable 7 1 1 1HAR

18 FLEX I/O Isolated Input HART Analog Module Publication 1794-IN115C-EN-P - April 2009Channel Data FormatsFormat(1)Bits Format NameSignal Range Us

FLEX I/O Isolated Input HART Analog Module 19Publication 1794-IN115C-EN-P - April 2009Cyclic HART Input DataThe HART input data holds the primary

2 FLEX I/O Isolated Input HART Analog Module Publication 1794-IN115C-EN-P - April 2009Important User InformationSolid state equipment has operation

20 FLEX I/O Isolated Input HART Analog Module Publication 1794-IN115C-EN-P - April 2009HART Input DataWord Bit15141312111098765432100 Reserved CH7C

FLEX I/O Isolated Input HART Analog Module 21Publication 1794-IN115C-EN-P - April 200950…61Words 2…13 for channel 462…73Words 2…13 for channel 574

22 FLEX I/O Isolated Input HART Analog Module Publication 1794-IN115C-EN-P - April 2009HART Input Data descriptionsCHn: HART CMD 3 Communication St

FLEX I/O Isolated Input HART Analog Module 23Publication 1794-IN115C-EN-P - April 2009Status IndicatorThe OK status indicator is bicolor, red, and

24 FLEX I/O Isolated Input HART Analog Module Publication 1794-IN115C-EN-P - April 2009Normal mode rejection ratio - current terminal>70 dB @ 50

FLEX I/O Isolated Input HART Analog Module 25Publication 1794-IN115C-EN-P - April 2009Wiring category(3)2 on signal ports 3 on power portsWire typ

26 FLEX I/O Isolated Input HART Analog Module Publication 1794-IN115C-EN-P - April 2009Environmental Attribute ValueTemperature, operating IEC 6006

FLEX I/O Isolated Input HART Analog Module 27Publication 1794-IN115C-EN-P - April 2009EFT/B Immunity IEC 61000-4-4: ±3 kV at 5 kHz on signal ports

Publication 1794-IN115C-EN-P - April 2009 PN-44688Supersedes Publication 1794-IN115B-EN-P - October 2008 Copyright © 2009 Rockwell Automation, Inc. Al

FLEX I/O Isolated Input HART Analog Module 3Publication 1794-IN115C-EN-P - April 2009Environment and Enclosure ATTENTIONThis equipment is

4 FLEX I/O Isolated Input HART Analog Module Publication 1794-IN115C-EN-P - April 2009Preventing Electrostatic Discharge ATTENTIONThis pro

FLEX I/O Isolated Input HART Analog Module 5Publication 1794-IN115C-EN-P - April 2009North American Hazardous Location Approval The following in

6 FLEX I/O Isolated Input HART Analog Module Publication 1794-IN115C-EN-P - April 2009European Hazardous Location Approval European Zone

FLEX I/O Isolated Input HART Analog Module 7Publication 1794-IN115C-EN-P - April 2009Install the ModuleRead this for information about how to inst

8 FLEX I/O Isolated Input HART Analog Module Publication 1794-IN115C-EN-P - April 20093. Make sure the pins on the bottom of the module are straigh

FLEX I/O Isolated Input HART Analog Module 9Publication 1794-IN115C-EN-P - April 20093. Connect the +V DC power lead to terminal 34 on the 34…51 r