Rockwell-automation 1790D-XXXX DeviceNet Analog Base D-Shell CompactBl Manual do Utilizador

1PRE Publication 1790-IN004B-EN-P - April 2001 2003Installation InstructionsDeviceNet Analog Base D-Shell CompactBlock LDX I/O(Cat. Nos. 1790D-N4C0,

10 Publication 1790-IN004B-EN-P - April 2003The required DeviceNet connector is not supplied with the block - you must purchase it separately

11Publication 1790-IN004B-EN-P - April 2003I/O Memory Mapping1790D-N4C0, -N4V0 Input Data FileWord/Bit Descriptions for 1790D-N4C0, -N4V0 Ana

12 Publication 1790-IN004B-EN-P - April 20031790D-N0C2, -N0V2 Output Data FileWord/Bit Descriptions for 1790D-N0C2, -N0V2 Analog Output Modul

13Publication 1790-IN004B-EN-P - April 2003I/O Channel LED Status Indicator1790D-N4V0 1790D-N4C0Status: Description: Status: Description:Flas

14 Publication 1790-IN004B-EN-P - April 2003I/O Channel LED Status Indicator1790D-N0V2 1790D-N0C2Status: Description: Status: Description:Fla

15Publication 1790-IN004B-EN-P - April 2003DeviceNet Analog Base D-Shell Block SpecificationsThe following table contains specifications that

16 Publication 1790-IN004B-EN-P - April 20031 Refer to publication 1770-4.1, Programmable Controller Wiring and Grounding Guidelines.2 See th

17Publication 1790-IN004B-EN-P - April 20034-Channel Analog Current Input Module Specifications1790D-N4C0Inputs per module 4 channel single-e

18 Publication 1790-IN004B-EN-P - April 20032 Channel Analog Current Output Module Specifications1790D-N0C2Outputs per module 2 channel singl

19Publication 1790-IN004B-EN-P - April 20034 Channel Analog Voltage Input Module Specifications1790D-N4V0Inputs per module 4 channel single-e

2 Publication 1790-IN004B-EN-P - April 2003Important User InformationBecause of the variety of uses for the products described in this public

20 Publication 1790-IN004B-EN-P - April 20032 Channel Analog Voltage Output Module Specifications1790D-N0V2Outputs per module 2 channel singl

21Publication 1790-IN004B-EN-P - April 2003The following information applies when operating this equipment in hazardous locations:Information

22 Publication 1790-IN004B-EN-P - April 2003

23Publication 1790-IN004B-EN-P - April 2003

Publication 1790-IN004B-EN-P - April 2003 PN957782-22Supersedes Publication 1790-IN004A-EN-P - November 2001 © 2003 Rockwell Au

3Publication 1790-IN004B-EN-P - April 2003ATTENTION!Identifies information about practices or circumstances that can lead to personal injury

4 Publication 1790-IN004B-EN-P - April 2003ATTENTION!Environment and EnclosureThis equipment is intended for use in a Pollution Degree 2 indu

5Publication 1790-IN004B-EN-P - April 2003Installing CompactBlock LDX I/OFollow these steps to install the block:1. Set the node address on t

6 Publication 1790-IN004B-EN-P - April 2003Mount the Base BlockYou can mount the base block to a panel or DIN rail. We recommend that you gro

7Publication 1790-IN004B-EN-P - April 20035. Replace the block on the panel and place a screw through each of the two mounting holes. Tighten

8 Publication 1790-IN004B-EN-P - April 2003Beginning with the base block, you can mount your expansion blocks either horizontally or vertical

9Publication 1790-IN004B-EN-P - April 20031790D-N0C2 Current Analog Input Module Wiring Diagram for D-Shell Connector• Wire pins 17, 18 and 1