Rockwell-automation 160 RSI SERIAL COMM MODULE Manual do Utilizador Página 26
- Página / 50
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
6–2 Parameter Descriptions
110 10 Read/Write [EPROM BAUD]
The baud rate used when SW1 & SW2 are set to “On” (EPROM Mode).
1 = 1200 Baud
2 = 2400 Baud
3 = 4800 Baud
4 = 9600 Baud
Drive power must be cycled before changes will take affect.
1 to 4 9600 Baud
111 11 Read/Write [Max ENQs]
The number of ENQs sent while waiting for a ACK or NAK.
0 to 255 3
112 12 Read/Write [Max NAKs]
Number of times module resends a message if response is NAK.
0 to 255 3
113 13 Read/Write [Message Timeout]
Amount of time (milliseconds) RS1 Module waits before sending an ENQ.
100 to 65535 100 Milliseconds
114 14 Read/Write [Comm App Timeout]
When logic command/status and reference/feedback messaging is active,
length of time in seconds from last DF1 message before faulting the drive.
0 to 65535 5 Seconds
115 15 Read [Packets Sent]
Number of DF1 packets sent.
0 to 65535 0
116 16 Read [Packets Received]
Number of DF1 packets received.
0 to 65535 0
117 17 Read [Undelivered Msgs]
Number of undelivered messages.
0 to 65535 0
118 18 Read [ENQs Sent]
Number of ENQs sent.
0 to 65535 0
119 19 Read [ENQs Received]
Number of ENQs received.
0 to 65535 0
120 20 Read [NAKs Received]
Number of NAKs received.
0 to 65535 0
121 21 Read [Bad Packets Rcvd]
Number of bad packets received (NAKed).
0 to 65535 0
122 22 Read [Duplicate Packet]
Number of duplicate packets received.
0 to 65535 0
123 23 Read [Out Memory NAKs]
Number of out of memory NAKs (messages coming faster than they can
be processed).
0 to 65535 0
124 24 Read [AppTimeout Cnt]
Number of application timeouts.
0 to 65535 0
125 25 Read/Write [Overrun Errors]
Action of the RS1 Module on a data rx overrun.
0 = Ignore
1 = Clear UART buffer
0 to 1 0
126 26 Read Only [Overrun Err Cnt]
Data Overrun Count.
0 to 65535 0
127 27 Read/Write [Force Fault]
Setting this parameter will fault the drive.
0 = No Action
1 = Fault the Drive
0 to 1 0
128 28 Read/Write [Reset RS1]
Setting this parameter to 1 will only reset the RS1 Module parameters to
factory settings.
Important: Drive parameters can be reset using P56 - [Reset Functions].
0 = No Action
1 = Resets RS1 parameters to defaults
0 to 1 0
129 29 Read/Write [Clr Comm Stats]
Setting this parameter to 1 will clear all diagnostic counters.
0 = No Action
1 = Clear all DF1 diagnostic counters (P115-124, 126)
0 to 1 0
Parameter Number
Access [Parameter Name] and Description
Min./Max.
Values Default
Drive
(N10:, N30:)
RS1
(N13:, N33:)
- User Manual 1
- Important User Information 2
- Table of Contents 3
- Chapter 7 4
- Chapter 8 4
- Chapter 9 4
- Appendix A 4
- Appendix B 4
- Using This Manual 5
- Reference Manuals 6
- Safety Precautions 6
- Product Overview 7
- Configuration DIP Switches 8
- Required Tools and Equipment 9
- Procedures 10
- Installation and Wiring 11
- Module Configuration Switches 12
- Setting the Protocol – SW3 13
- Module Installation/Removal 14
- Removing the RS1 Module 15
- Wiring the Connector 16
- - continued 17
- Connecting the Communication 18
- Cable to the Module 18
- Modes of Operation 19
- RS1 Data Table Interface 21
- Refer to table on next page 22
- Data is formatted as follows: 23
- 5–4 RS1 Data Table Interface 24
- Parameter Descriptions 25
- (N10:, N30:) 26
- (N13:, N33:) 26
- End of Chapter 6 28
- Using the RS1 Module with 29
- DriveExplorer™ Software 29
- Setting Baud Rates and 30
- Configuring the 30
- Communications Port 30
- Monitoring and Editing 30
- Parameters 30
- Uploading Editable Parameters 31
- Downloading Parameters 31
- End of Chapter 7 32
- Using the RS1 Module with a 33
- Programmable Controller 33
- Program the Ladder 35
- Reading and Writing 36
- Program the Ladder for 37
- Parameter Reads and Writes 37
- Figure 8.4 38
- Troubleshooting 39
- READY LED 40
- COMM LED 40
- FAULT LED 40
- RS1/DF1 Error Codes 41
- End of Chapter 9 42
- Specifications 43
- End of Appendix A 44
- RS1 Module Compatibility 45
- End of Appendix B 46
- I–2 Index 48
Manuais e produtos relacionados com Equipamento Rockwell-automation 160 RSI SERIAL COMM MODULE
Equipamento Rockwell-automation 22-WIM-N1 DSI Wireless Interface Module Manual do Utilizador
(100 páginas)
(100 páginas)
Equipamento Rockwell-automation 140U-M-NH12_NH21 NFPA 79 Internal Rotary Operating Manual do Utilizador
(2 páginas)
(2 páginas)
Equipamento Rockwell-automation 193-EIMD60 E3 Overload Relay AC Input Interface Mo Manual do Utilizador
(4 páginas)
(4 páginas)
Equipamento Rockwell-automation 802 Neutral Position Plug-In Limit Switch Manual do Utilizador
(2 páginas)
(2 páginas)
Equipamento Rockwell-automation 140G-..-Fx Flexible Cable Oper Mech Manual do Utilizador
(8 páginas)
(8 páginas)
Equipamento Rockwell-automation 800E UL Requirements for Metal Enclosures Manual do Utilizador
(1 páginas)
(1 páginas)
Equipamento Rockwell-automation 193-EF Electronic Motor Protection Relay Manual do Utilizador
(16 páginas)
(16 páginas)
Equipamento Rockwell-automation 140 Undervoltage / Shunt Trip Devices for 140-CMN Manual do Utilizador
(2 páginas)
(2 páginas)
Equipamento Rockwell-automation 25B PowerFlex 520-Series Replacement Power Termina Manual do Utilizador
(2 páginas)
(2 páginas)
Equipamento Rockwell-automation 825-MDN Smart Motor Manager DeviceNet Communicatio Manual do Utilizador
(70 páginas)
(70 páginas)
Equipamento Rockwell-automation 140 Lockable Twist Knobs for 140-CMN Manual do Utilizador
(2 páginas)
(2 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.134 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais